CMIT 351 Project 1: Design and Implement a LAN

CMIT 351 Project 1: Design and Implement a LAN
Design a Native Space Community utilizing switches and hosts (computer systems)• Create primary change configurations vital for change upkeep and operation• Outline Digital LANs (VLANs) to implement segmentation• Implement vital VLAN trunking to increase a VLAN throughout the LAN

Model 1.zero
CMIT 351 Project 1 Description
Intro:
ACME College IT needs to implement layer 2 segmentation to manage broadcast domains and
enhance Native Space Community (LAN) efficiency.
State of affairs:
IT has tasked you with creating a prototype of the brand new LAN. You must doc the
prototype and determine what works in addition to what doesn’t work. The necessities you may have
specify a most variety of change (2), the variety of digital LANs (VLANs) as three, and
some computer systems for endpoint testing.
Overview
Trendy switches use VLANs to enhance community efficiency by separating massive Layer 2
broadcast domains into smaller ones. VLANs may also be used as a safety measure by
controlling which hosts can talk. Normally, VLANs make it simpler to design a community
to assist the targets of a corporation. VLAN trunks are used to span VLANs throughout a number of
units. Trunks permit the visitors from a number of VLANS to journey over a single hyperlink, whereas
holding the VLAN identification and segmentation intact.
Goals
• Design a Native Space Community utilizing switches and hosts (computer systems)
• Create primary change configurations vital for change upkeep and operation
• Outline Digital LANs (VLANs) to implement segmentation
• Implement vital VLAN trunking to increase a VLAN throughout the LAN
Instruments
• You have to a diagramming software akin to draw.io or Visio to finish Half 1.
• You possibly can reference the next uCertify labs for assist in constructing the change
configurations: Modules 5, 6, 7, eight, 9, and 10.
• Notice: entry to bodily or emulated Cisco units will not be required to finish this
mission. Nevertheless, if you wish to take a look at, follow, or in any other case tinker you will get Cisco
Packet Tracer (https://skillsforall.com/course/getting-started-cisco-packet-tracer) or
GNS3 (https://www.gns3.com/)
Half 1: Design the Native Space Community
The work milestones for this a part of the mission are as follows:
• The LAN should consist of two switches and three computer systems.
• The 2 switches have to be named S1 and S2.
• The three computer systems have to be named PC-A, PC-B, and PC-C.
Half 2: Create the fundamental change configurations
Your community engineering lead has accepted the LAN design. Now, the work to implement the
design can start. Your duties are as follows:
2.1 Cable the community
Model 1.zero
• Join PC-A to S1 on Ethernet Interface 6
• Join S1 to S2 on Ethernet Interfaces 1
• Join PC-B to S2 on Ethernet Interface 11
• Join PC-C to S2 on Ethernet Interface 18
2.2. Configure the fundamental change features
Configure the fundamental features in each S1 and S2 as follows:
• Set the allow secret to “class”
• Set the road con zero password to “cisco”
• Set the road vty zero 15 password to “cisco”
• Set the MOTD to “Unauthorized entry is strictly prohibited.”
• Set logging to synchronous
2.three Configure the computer systems
Configure the three computer systems as follows:
Title IP Handle Subnet Gateway
PC-A 192.168.10.three 255.255.255.zero 192.168.10.1
PC-B 192.168.10.four 255.255.255.zero 192.168.10.1
PC-C 192.168.20.three 255.255.255.zero 192.168.20.1
2.four Check and Validate Connectivity
Use ping to check connectivity between the computer systems. Element your ends in your mission
doc, each what works and what doesn’t work.
Half three: Outline the VLANs
three.1 You must outline three VLANs in each S1 and S2 as follows:
• VLAN 10 College students
• VLAN 20 College
• VLAN 99 Administration
three.2 Then, outline the next interfaces for the VLANs as:
Gadget Interfaces VLAN / IP Handle
S1 6, 12 – 20, 22-23 VLAN 10
S1 11,21 VLAN 20
S1 VLAN 99 192.168.1.11 255.255.255.zero
S2 11 VLAN 10
S2 18 VLAN 20
S2 VLAN 99 192.168.1.12 255.255.255.zero
Model 1.zero
Half four: Implement VLAN Trunking
four.1 Implement VLAN trunking on the switches as follows:
• Manually set interface 1 on S1 and S2 to trunk (don’t use mode dynamic fascinating)
four.2 Use ping to check connectivity between the computer systems and switches. Element your ends in your
mission doc, each what works and what doesn’t work.